View STGB10NC60KD_4924249.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

STGB10NC60KD, STGD10NC60KD STGF10NC60KD, STGP10NC60KD
10 A, 600 V short-circuit rugged IGBT
Features

TAB TAB
3
Lower on voltage drop (VCE(sat)) Lower CRES / CIES ratio (no cross-conduction susceptibility) Very soft ultra fast recovery antiparallel diode Short-circuit withstand time 10s
2
3 1
1
DPAK
TAB
D PAK
Description
This IGBT utilizes the advanced PowerMESHTM process resulting in an excellent trade-off between switching performance and low on-state behavior.
3 1 2
1 3 2
TO-220FP
TO-220
Applications

Figure 1.
Internal schematic diagram
High frequency motor controls SMPS and PFC in both hard switch and resonant topologies Motor drives
Table 1.
Device summary
Marking GB10NC60KD GD10NC60KD GF10NC60KD GP10NC60KD Packages D2PAK Tape and reel DPAK TO-220FP Tube TO-220 Packaging
Order codes STGB10NC60KDT4 STGD10NC60KDT4 STGF10NC60KD STGP10NC60KD
November 2009
Doc ID 11423 Rev 6
1/20
www.st.com 20
Contents
STGx10NC60KD
Contents
1 2 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Electrical characteristics (curves) ............................. 8
3 4 5 6
Test circuits
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2/20
Doc ID 11423 Rev 6
STGx10NC60KD
Electrical ratings
1
Table 2.
Electrical ratings
Absolute maximum ratings
Value
Symbol
Parameter
DPAK TO-220
Unit DPAK 600 20 10 30 30 20 10 20 9 6 TO-220FP V A A A A V A A 25 2500 10 W V s
VCES IC(1) IC(1) ICL(2) ICP(3) VGE IF IFSM PTOT VISO tscw Tstg Tj
Collector-emitter voltage (VGE = 0) Continuous collector current at TC = 25C Continuous collector current at TC = 100C Turn-off latching current Pulsed collector current Gate-emitter voltage Diode RMS forward current at Tc=25C Surge non repetitive forward current Tp = 10 ms sinusoidal Total dissipation at TC = 25C Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1s;TC=25C) Short-circuit withstand time , VCE = 0.5 VCES, Tj = 125 C, RG = 10 VGE = 12 V Storage temperature 65 --
62
- 55 to 150 Operating junction temperature
C
1. Calculated according to the iterative formula
T j ( max ) - T C I C ( T C ) = --------------------------------------------------------------------------------------------------------R thj - c x V CE ( sat ) ( max ) ( T j ( max ), I C ( T C ) )
2. Vclamp = 80 % VCES, VGE = 15 V, RG = 10 , TJ = 150 C 3. Pulse width limited by maximum junction temperature and turn-off within RBSOA
Doc ID 11423 Rev 6
3/20
Electrical ratings
STGx10NC60KD
Table 3.
Thermal data
Value
Symbol
Parameter
TO-220 DPAK
Unit DPAK 2 4.5 100 TO-220FP 5 7 62.5 C/W
Rthj-case Rthj-case Rthj-amb
Thermal resistance junction-case IGBT Thermal resistance junction-case diode Thermal resistance junction-ambient
1.9 4 62.5
4/20
Doc ID 11423 Rev 6
STGx10NC60KD
Electrical characteristics
2
Electrical characteristics
(Tj =25C unless otherwise specified) Table 4.
Symbol
Static
Parameter Test conditions IC= 1mA Min. Typ. Max. Unit
Collector-emitter V(BR)CES breakdown voltage (VGE= 0) VCE(sat) VGE(th) ICES IGES gfs(1)
600 2.2 1.8 4.5 2.5
V V V V A mA nA S
Collector-emitter saturation VGE= 15V, IC= 5A voltage VGE= 15V, IC= 5A, Tj= 125C Gate threshold voltage Collector cut-off current (VGE = 0) Gate-emitter leakage current (VCE = 0) Forward transconductance VCE= VGE, IC= 250A VCE= 600 V VCE=600 V, Tj = 125C VGE= 20V VCE = 15V, IC= 5A
6.5 150 1 100 15
1. Pulse test: pulse duration < 300 s, duty cycle < 2 %
Table 5.
Symbol Cies Coes Cres Qg Qge Qgc
Dynamic
Parameter Input capacitance Output capacitance Reverse transfer capacitance Total gate charge Gate-emitter charge Gate-collector charge Test conditions VCE = 25V, f = 1MHz, VGE = 0 VCE = 390V, IC = 5A, VGE = 15V, (see Figure 19) Min. Typ. Max. 380 46 8.5 19 5 9 Unit pF pF pF nC nC nC
-
-
-
Doc ID 11423 Rev 6
5/20
Electrical characteristics
STGx10NC60KD
Table 6.
Symbol td(on) tr (di/dt)on td(on) tr (di/dt)on tr(Voff) td(off) tf tr(Voff) td(off) tf
Switching on/off (inductive load)
Parameter Turn-on delay time Current rise time Turn-on current slope Turn-on delay time Current rise time Turn-on current slope Off voltage rise time Turn-off delay time Current fall time Off voltage rise time Turn-off delay time Current fall time Test conditions VCC = 390V, IC = 5A RG= 10 VGE= 15V , (see Figure 20) VCC = 390V, IC = 5A , RG= 10 VGE= 15V, Tj=125C (see Figure 20) Vcc = 390V, IC = 5A, , RGE = 10 VGE = 15V (see Figure 20) Vcc = 390V, IC = 5A, , RGE=10 VGE =15V, Tj=125C (see Figure 20) Min. Typ. 17 6 655 16.5 6.5 575 33 72 82 60 106 136 Max. Unit ns ns A/s ns ns A/s ns ns ns ns ns ns
-
-
-
-
Table 7.
Symbol Eon(1) Eoff(2) Ets Eon(1) Eoff(2) Ets
Switching energy (inductive load)
Parameter Turn-on switching losses Turn-off switching losses Total switching losses Test conditions VCC = 390V, IC = 5A , RG= 10 VGE=15V (see Figure 20) VCC = 390V, IC = 5A RG= 10 VGE= 15V, , Tj= 125C (see Figure 20) Min. Typ. 55 85 140 Max. Unit J J J
-
Turn-on switching losses Turn-off switching losses Total switching losses
87 162 249
-
J J J
1. Eon is the tun-on losses when a typical diode is used in the test circuit in figure 2. If the IGBT is offered in a package with a co-pak diode, the co-pack diode is used as external diode. IGBTs & Diode are at the same temperature (25C and 125C) 2. Turn-off losses include also the tail of the collector current
6/20
Doc ID 11423 Rev 6
STGx10NC60KD
Electrical characteristics
Table 8.
Symbol VF trr Qrr Irrm trr Qrr Irrm
Collector-emitter diode
Parameter Forward on-voltage Reverse recovery time Reverse recovery charge Reverse recovery current Reverse recovery time Reverse recovery charge Reverse recovery current Test conditions IF=5 A IF=5 A, Tj=125 C IF=5 A, VR=40 V, di/dt=100 A/s (see Figure 5) IF=5 A, VR=40 V, Tj=125 C, di/dt=100 A/s (see Figure 5) Min Typ. 2 1.6 22 14 1.3 35 40 2.2 Max. Unit V V ns nC A ns nC A
-
-
-
-
Doc ID 11423 Rev 6
7/20
Electrical characteristics
STGx10NC60KD
2.1
Figure 2.
Electrical characteristics (curves)
Output characteristics Figure 3. Transfer characteristics
Figure 4.
Transconductance
Figure 5.
Collector-emitter on voltage vs temperature
Figure 6.
Gate charge vs gate-source voltage Figure 7.
Capacitance variations
8/20
Doc ID 11423 Rev 6
STGx10NC60KD Figure 8. Normalized gate threshold voltage vs temperature Figure 9.
Electrical characteristics Collector-emitter on voltage vs collector current
Figure 10. Normalized breakdown voltage vs temperature
Figure 11. Switching losses vs temperature
Figure 12. Switching losses vs gate resistance Figure 13. Switching losses vs collector current
Doc ID 11423 Rev 6
9/20
Electrical characteristics Figure 14. Thermal impedance for DPAK, DPAK and TO-220 Figure 15. Turn-off SOA
STGx10NC60KD
Figure 16. Emitter-collector diode characteristics
Figure 17. Thermal impedance for TO-220FP
10/20
Doc ID 11423 Rev 6
STGx10NC60KD
Test circuits
3
Test circuits
Figure 19. Gate charge test circuit
Figure 18. Test circuit for inductive load switching
Figure 20. Switching waveform
Figure 21. Diode recovery time waveform
Doc ID 11423 Rev 6
11/20
Package mechanical data
STGx10NC60KD
4
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark.
12/20
Doc ID 11423 Rev 6
STGx10NC60KD Table 9.
Dim. Min. A A1 b b2 c c2 D D1 E E1 e e1 H J1 L L1 L2 R V2 0 4.88 15 2.49 2.29 1.27 1.30 0.4 8 0 4.40 0.03 0.70 1.14 0.45 1.23 8.95 7.50 10 8.50 2.54 5.28 15.85 2.69 2.79 1.40 1.75 0.192 0.590 0.099 0.090 0.05 0.051 10.40 Typ. Max. 4.60 0.23 0.93 1.70 0.60 1.36 9.35 Min. 0.173 0.001 0.027 0.045 0.017 0.048 0.352 0.295 0.394 0.334
Package mechanical data D2PAK package mechanical data
mm inch Typ. Max. 0.181 0.009 0.037 0.067 0.024 0.053 0.368
0.409
0.1 0.208 0.624 0.106 0.110 0.055 0.069 0.016 8
Figure 22. D2PAK package drawing
0079457_M
Doc ID 11423 Rev 6
13/20
Package mechanical data Table 10.
Dim. Min. A A1 A2 b b4 c c2 D D1 E E1 e e1 H L L1 L2 L4 R V2 0
o
STGx10NC60KD
DPAK package mechanical data
mm Typ Max. 2.40 1.10 0.23 0.90 5.40 0.60 0.60 6.20 5.10 6.40 4.70 2.28 4.40 9.35 1 2.80 0.80 0.60 0.20 8o 1 4.60 10.10 6.60
2.20 0.90 0.03 0.64 5.20 0.45 0.48 6.00
Figure 23. DPAK package drawing
0068772_G
14/20
Doc ID 11423 Rev 6
STGx10NC60KD Table 11.
Dim. Min. A B D E F F1 F2 G G1 H L2 L3 L4 L5 L6 L7 Dia 28.6 9.8 2.9 15.9 9 3 4.4 2.5 2.5 0.45 0.75 1.15 1.15 4.95 2.4 10 16 Typ.
Package mechanical data TO-220FP package mechanical data
mm Max. 4.6 2.7 2.75 0.7 1 1.70 1.70 5.2 2.7 10.4
30.6 10.6 3.6 16.4 9.3 3.2
Figure 24. TO-220FP package drawing
L7 E
A B
D Dia L6 L5
F1
F2 F
H G1
G
L2 L3
L4
7012510_Rev_K
Doc ID 11423 Rev 6
15/20
Package mechanical data Table 12.
Dim. Min. A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 P Q 3.75 2.65 10 2.40 4.95 1.23 6.20 2.40 13 3.50 16.40 28.90 4.40 0.61 1.14 0.48 15.25 1.27 Typ.
STGx10NC60KD
TO-220 type A mechanical data
mm Max. 4.60 0.88 1.70 0.70 15.75
10.40 2.70 5.15 1.32 6.60 2.72 14 3.93
3.85 2.95
Figure 25. TO-220 type A package drawing
0015988_S
16/20
Doc ID 11423 Rev 6
STGx10NC60KD
Packaging mechanical data
5
Packaging mechanical data
D 2 PAK FOOTPRINT
TAPE AND REEL SHIPMENT
REEL MECHANICAL DATA
DIM. A B C D G N T 1.5 12.8 20.2 24.4 100 30.4 26.4 13.2 mm MIN. MAX. 330 0.059 0.504 0.520 0795 0.960 1.039 3.937 1.197 BULK QTY 1000 inch MIN. MAX. 12.992
TAPE MECHANICAL DATA
DIM. A0 B0 D D1 E F K0 P0 P1 P2 R T W mm MIN. 10.5 15.7 1.5 1.59 1.65 11.4 4.8 3.9 11.9 1.9 50 0.25 23.7 24.3 MAX. 10.7 15.9 1.6 1.61 1.85 11.6 5.0 4.1 12.1 2.1 inch MIN. MAX. 0.413 0.421 0.618 0.626 0.059 0.063 0.062 0.063 0.065 0.073 0.449 0.456 0.189 0.197 0.153 0.161 0.468 0.476 0.075 0.082 1.574 0.35 0.0098 0.0137 0.933 0.956
BASE QTY 1000
Doc ID 11423 Rev 6
17/20
Packaging mechanical data
STGx10NC60KD
DPAK FOOTPRINT
All dimensions are in millimeters
TAPE AND REEL SHIPMENT
REEL MECHANICAL DATA
DIM. A B C D G N T 1.5 12.8 20.2 16.4 50 22.4 18.4 13.2 mm MIN. MAX. 330 0.059 0.504 0.520 0.795 0.645 0.724 1.968 0.881 BULK QTY 2500 inch MIN. MAX. 12.992
TAPE MECHANICAL DATA
DIM. A0 B0 B1 D D1 E F K0 P0 P1 P2 R
W
BASE QTY 2500
mm MIN. 6.8 10.4 1.5 1.5 1.65 7.4 2.55 3.9 7.9 1.9 40
15.7 16.3
inch MIN. MAX. 7 0.267 0.275 0.409 0.417 0.476 0.059 0.063 0.059 0.065 0.073 0.291 0.299 0.100 0.108 0.153 0.161 0.311 0.319 0.075 0.082 1.574
0.618 0.641
MAX. 10.6 12.1 1.6 1.85 7.6 2.75 4.1 8.1 2.1
18/20
Doc ID 11423 Rev 6
STGx10NC60KD
Revision history
6
Revision history
Table 13.
Date 14-Jun-2005 19-Jul-2005 27-Jan-2006 01-Mar-2006 08-Feb-2007 24-Nov-2009
Document revision history
Revision 1 2 3 4 5 6 New release. Complete version. Inserted ecopack indication. The document has been reformatted. Modified value on Table 6.: Switching on/off (inductive load). Inserted DPAK package option. Changes
Doc ID 11423 Rev 6
19/20
STGx10NC60KD
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
20/20
Doc ID 11423 Rev 6

▲Up To Search▲

Price & Availability of STGB10NC60KD

	To Download STGB10NC60KD Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .